DIFF�RENTIELS / AXLE / PONTS , toutes marques...

[Cadpat]

Un petit transfert...

Envoyé par Lafchar

Spicer/Dana manuals from D30 thru D70 axles in PDF form

Cela peut-ëtre utile.

http://www2.dana.com/expertforms/depdf.aspx?prod=AXL

[nitromyke]

Quelques infos que j'ai trouvé :


Ring Gear Bolts10 - 10mm boltsRing Gear Diameter6.90 Inches
Pinion Shaft Diameter/Splines1.379"/26
Axle Shaft Diameter / Splines.940 / 22 (Front)1.05 / 26 (Rear)
Axle Tube Material / Diameter / Wall ThicknessHREW / 2.56 / .120
Gear Ratio 3.73 Available
Aftermarket Ratios 4.57, 5.38
Carrier Breaks None
Recommended Max Tire Size 32-Inches
Pinion Bearing Preload 7.8-14.7 in-lbs
Backlash.004-.006 in.
Ring Gear Torque 58-65 lbs-ft
Carrier Bearing Cap Torque 51-72 lbs-ft
Pinion Nut Torque Zero endplay (crush sleeve)
Suspension Leaf Spring
Important Note:In 1990 the front axle was changed to a 2-pinion type and will not fit the available lockers.



La configuration d'origine pour la suspension sont les lames sous les tubes d'essieux. Les deux coeurs de differentiels sont du coté passager, et de type "open". Freins avant a disques,arriere a tambour.

Pour la largeur des housings; les '86 et + on 3" plus large que ses predecesseurs, La distance exterieurs des springs perch avant est de 27" pour les narrows, et 30" pour les 86+.

*Les shafts avant en chromo aftermarket sont fait pour les 86+, et necessitent l'usage d'un differentiel arriere de 26 splines. Le third member complet peut etre transferer de l'arriere a l'avant.

*Les gears avant de Sidekick peuvent etre transférés dans les deux differentiels de Samurai. Choix de 4:64 ou 5:12 selon la transmission du Sidekick.

*Freins avants ventilés de Sideckick 4 portes sont bolt-on sur le differentiel avant. Les splash guard on besoin d'une legere trim pour les plus gros calipers. Les brackets de caliper du Sidekick 4 portes doivent etre utilisées.

Source: http://zukioffroad.com/Tech_Library/index.htm

[nitromyke]

1 - Hub R/L 43400-80812
2 - Bearing, Hub(2/side) R/L 09265-41001
3 - Seal, Bearing R/L 09283-50002
4 - Caliper, Brake
To VINJ4235000 R/L 55100-B3300
From VIN J4235001 R/L 55100-70A20
5 - Carrier, Caliper R/L 55160-70A10
6 - Carrier, Caliper R/L 55311-80000
7 - Shield, Splash R/L 55221-80000
8 - Rotor, Brake R/L 55211-80000
9 - Spindle, Assembly R/L 43440-80005
10 - Bushing, Spindle R/L 43445-60A11 (Included w/ Spindle Assembly)
11 - Knuckle R 45111-80001, L 45151-80001
12 - Retainer, Oil Seal (2/Sides) R/L 45623-80001
13 - Hub Kit, Locking
Manual Lock Hubs R/L 43801-80011
Automatic Lock Hubs R/L 43801-83000
14 - Pin, King (2/Sides) R/L 45610-63002
15 - Shaft, Axle R 44101-83320, L 44102-83320
16 - Seal, Oil R/L 09283-26016
17 - Housing , Axle 46480-83304
18 - Hosing, Axle R/L 51540-80151

[Cadpat]

D30/35 general info: These have great aftermarket support with axle and lockers. They tend to hold up to mild off-road use with lockers and up to 33" tires. Tend to have the smallest brakes so stopping larger tires will be more work for them. The weak part of the D30 is the front u-joints typically. The weak part of the D35 are the axle tubes and their c-clip axles. If you break a D35 axle and you have drum brakes, your wheel and what's left of your axle can come right out on the trail.

D44 general info: These have great aftermarket support with axle and lockers. They came from 1/2 ton truck or HD vehicles (wagoneers, cherokee's). They are a common upgrade for ZJ/XJ/WJ owners looking for a HD axle. This axle with it's 33 spline axles can handle 35"-39" tires with lockers in mild to extreme conditions. They have better brakes to help stop larger tires. The downside is they are heavier then the D30/D35 axles. Another downside is they will not bolt-in, which means you'll have to weld on the correct axle brackets.

D60 general info: These have great aftermarket support with axle and lockers. One of the most HD axles out there as they were used in 3/4 to 1 ton trucks. They have the largest axles (35 spline and even 40 spline) and are meant for extreme trail use. They have better brakes then D44's. The downside is they are heavier then the D44 axles and because the housing is larger, you'll loose a little ground clearance. Another downside is they will not bolt-in, which means you'll have to weld on the correct axle brackets. Many times they are the wrong width as well, so you may have to modify the width of these to make them fit.

Ford 8.8" and 9" general axle info: This is a very good upgrade as the aftermarket is plentiful and those axles were found in many applications. Can be upgraded easily to 40 spline shafts for racing applications. That means brake conversions are plentiful. Lastly, they are cheap and easy to find while being very stout axle that is the right width.

[Cadpat]

XJ Cherokee 1995 et -


Pre-95 Cherokee XJ

• Front Axle: Dana 30 with a vaccuum disconnect
  • Differential Location: Drivers side
  • Stock axle splines: 27 (upgradeable to 30 splines)
  • Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes: This was not the most desirable axle due to the vaccume disconnect which was prone to failure. A Dana 30 from a '95 1/2 or later XJ/ZJ is a common upgrade which eliminates the vaccume disconnect. If you choose the 95+ XJ D30 it is a a stronger High-pinion version. Many lockers are available for the D30 axle.
• Rear Axle: Dana 35 with c-clips or Chrysler 8.25"
  • Differential Location: Centered
  • Stock axle splines: 27 (upgradeable to 30 splines)
  • Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes for D35: Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 35 kit. The weak part of this axle is the axle tubes. Under extreme pressure they flex which results in broken axles or pinion failures.

[Cadpat]

XJ Cherokee 1995 1/2 +

95 1/2+ Cherokee's

• Front axle: High pinion D30
  • Differential Location: Drivers side
  • Stock axle splines: 27 (upgradeable to 30 splines)
    Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes: Stronger the earlier D30's. Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 30 kit. The u-joints are the main weak point and can be easily upgraded. Available thru 1999. 2000-2001 have a front D30 almost identical to the TJ, so it is low pinion
• Rear axle: Dana 35 c-clip or Chrsyler 8,25 OR D44 (very rare)
  • Differential Location: Centered
  • Stock D35 axle splines: 27 (upgradeable to 30 splines)
    Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes: Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 35 kit. The weak part of this axle is the axle tubes. Under extreme pressure they flex which results in broken axles or pinion failures.

[Cadpat]

ZJ 1993-1998 with Inline 6 4.0L

93-98 I6 Grand Cherokee's

• D30 low pinion front axle
  • Differential Location: Drivers side
  • Stock axle splines: 27 (upgradeable to 30 splines)
  • Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes: Stronger the earlier D30's. Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 30 kit. The u-joints are the main weak point and can be easily upgraded.
• D35 c-clip rear axle
  • Differential Location: Centered
  • Stock D35 axle splines: 27 (upgradeable to 30 splines)
  • Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes: Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 35 kit. The weak part of this axle is the axle tubes. Under extreme pressure they flex which results in broken axles or pinion failures.

ZJ 1993-1998 with V8 (5,2L - 5,9L)

93-98 V8 (5.2L or 5.9L) Grand Cherokee's

• D30 low pinion front axle
  • Differential Location: Drivers side
  • Stock axle splines: 27 (upgradeable to 30 splines)
  • Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes: Stronger the earlier D30's. Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 30 kit. The u-joints are the main weak point and can be easily upgraded.
• D44a "aluminum center section" rear axle
  • Differential Location: Centered
  • Stock axle splines: 27 (upgradeable to 30 splines)
  • Lug Pattern: 5 on 4.5"
  • Width: 60" from wheel mounting surface to wheel mounting surface
  • Notes for D44a: Not a bad axle with 33" or smaller tires. The aftermarket is very limited for this axle due to the aluminum center section in the axle. The center section is very similar to the unit in the corvette. Many people replace the axle due to the limited gear ratio's available and the extremely limited availability of any traction device such as a locker.

[Cadpat]

WJ 1999-2004

99-04 Grand Cherokee WJ

• Front axle: High pinion D30
  • Differential Location: Drivers side
  • Stock axle splines: 27 (upgradeable to 30 splines)
    Lug Pattern: 5 on 5"
  • Width: 65" from wheel mounting surface to wheel mounting surface
  • Notes: Stronger the earlier D30's. Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 30 kit. The u-joints are the main weak point and can be easily upgraded.
• D35 c-clip rear axle
  • Differential Location: Centered
  • Stock D35 axle splines: 27 (upgradeable to 30 splines)
    Lug Pattern: 5 on 5"
  • Width: 65" from wheel mounting surface to wheel mounting surface
  • Notes: Not a bad axle with 33" or smaller tires. Many people upgrade this axle with 30 spline axles and lockers. The upgrade many times is known as a SUPER 35 kit. The weak part of this axle is the axle tubes. Under extreme pressure they flex which results in broken axles or pinion failures.

[Cadpat]

Popular Axle Upgrades:

• Front Axle upgrades to replace the Dana 30 low pinion (in early XJ's and ZJ's)
  • High pinion D30 out of a 95+ XJ
    • Notes: This would be a bolt-in! 4 cylinder XJ versions have 4.10 gears! This also has larger 760 u-joints!
  • 80-91 Wagoneer Narrow-Track Dana 44
    • Differential Location: Drivers side
    • Lug pattern: 6 on 5.5"
    • Stock axle splines: 30 spline is common (upgradeable to 35 spline)
    • Width: 60" from wheel mounting surface to wheel mounting surface
    • Notes: Right width for XJ or ZJ's, can be converted for 5 on 5.5 or 8 on 6.5" lug pattern, they are relatively cheap and easily found. Avoid the vacuum disconnect version.
    • Identified by: stop sign like diff cover, spring-under housing, 60" width
• Rear axle upgrades to replace the D35 and D44a (in XJ or ZJ's)
  • 93-Up Isuzu Rodeo/Honda passport D44
    • Differential location: Centered
    • Lug pattern: 6 on 5.5"
    • Stock axle splines: 30 spline is common (upgradeable to 35 spline)
    • Width: 58" wide (2" narrower then XJ or ZJ)
    • Notes: Many came with 4.30 or 4.56 gears stock and disk brakes
    • Identified by: sometimes will have cast aluminum diff cover, looks like normal D44, goofy sensor/wire on top of housing
  • 96+ Ford Explorer 8.8 c-clip axle
    • Differential location: Centered
    • Lug pattern: 5 on 4.5"
    • Stock axle splines: 31 spline is common (upgradeable to 35 spline)
    • Width: 58 1/4" wide (2" narrower then XJ or ZJ)
    • Notes: 8.8's out of rangers and mustangs will not work, so be careful. A common upgrade is the Super88 which comes with larger axles. Very strong with stock axles and many came with limited slip, 4.10 gears, and disk brakes stock.
• Front axle upgrades for WJ D30's (65" width axles)
  • 74-79 Cherokee Chief/J-truck Wide-track D44
    • Differential location: Passenger side
    • Lug pattern: 6 on 5.5" and 8 on 6.5"
    • Stock axle splines: 30 spline is common (upgradeable to 35 spline)
    • Width: 66" wide (1" wider then WJ)
    • Notes: Has HD axle tubes, easy to convert to other lug patterns
  • New Wrangler Rubicon JK axles D44
    • Differential location: Passenger
    • Lug pattern: 5 on 5.5"
    • Stock axle splines: 30 splines (with factory e-locker)
    • Width: 66.75" wide (1.75" wider then factory)
    • Notes: Comes with factory e-locker, but will need the mounting brackets welded on. A factory wiring switch can be used for a factory look and function.
• Rear axle upgrades for WJ D35's (65" width axles"
  • 74-86 F150 and Bronco Ford 9"
    • Differential Location: Centered
    • Lug pattern: 5 on 5.5"
    • Stock axle splines: 31 spline axles (upgradeable to 35/40 spline)
    • Width: 65" wide
    • Notes: Axles from 2wd vehicles had 28 spline axles, but still can be converted to 35/40 splines.
    • Identified by: A removable third member and stamped sheet metal housing without removable diff cover.
  • New Wrangler JK Dana 44
    • Differential Location: Centered
    • Lug pattern: 5 on 5.5"
    • Stock axle splines: 31 spline axles
    • Width: 66.75" wide (1.75" wider then factory)
    • Notes: Comes with factory e-locker, but will need all the bracketry welded on to mount in WJ. Comes with stock 4.10 gears!

[Cadpat]

POIDS (en livres - lbs) de différents axles - Un gros merci à Maxim36 qui a tiré l'info de Pirate4x4

Front axle

Zuk = 165
Toyota = 220
Dana 30 tj = 230
Spider 9 = 325
Diamond toy = 350
Camo’s 60 =355
Dana 44 60wms = 386

609 = 400-450 depending on wall size and inner c’s
Dana 44 full width = 450
Dana 60 ford = 485
Dana 60 chevy = 525
Volvo = 600
Mog 404 =600
Mog 406 = 650
Rockwell w/o drums and narrowed = 662
Rockwell w/o drums = 682
U1300 = 710
rockwell w/ drums = 842lbs

toy housing = 50
Diamond 609 w/ .25 wall chromo and stock 60 inner C's = 68
Diamond 609 w/ .375 wall dom with Dedenbear inners = 100
dana 60 housing = 160


Rear axle

Zuk = 130
Toyota = 150
Dana 44 tj = 150
Camo’s 60 =225
Ford 9 =225
Dana 44 fw = 250
Dana 60 =300
Corp 14sf 3/4 ton version w/ disc = 375
Corp 14sf 3/4 ton w/ drums = 420
Corp 14ff w/disc = 475
Dana 70hd =480
Dana 80 = 505
Rockwell w/o drums = 532
Corp 14ff = 550
Mog 404 = 550
Mog 406 = 620
rockwell stock = 692