DIFF�RENTIELS / AXLE / PONTS , toutes marques...

[Cadpat]

INFOS DANA 60 AVANT et ARRIÈRE

Direct de Wikipedia, merci à Samurai01 pour la belle trouvaille !

http://en.wikipedia.org/wiki/Dana_60

Common Applications


Front Axle


International Harvester

• 1975 1300 Camper Special

Chevrolet

• 1977-1991 1Ton (K30/V30)
• 1984-1988 Commercial Utility Cargo Vehicle

Dodge

• 1975-2002 3/4 Ton (D-600/W-250/2500)
• 1981-2002 1 Ton (D-700/W-350/3500)

Ford

• 1974-1979 F-250
• 1999-2011 F-250 (Optional)
• 1974-2011 F-350
• 2000-2004 F-450/F-550

'Dana Super 60'

• • 2005-2010 F-450/F-550 (Dana Super 60)
  • 2011 F-550 and class 4 F-450.

Rear Axle



Studebaker

• 1956-1964 E12 3/4t and E14 1t

Dodge

• 1966-1970 Coronet & R/T
• 1966-1972 Charger & R/T
• 1968-1972 Super Bee
• 1970-1971 Challenger
• 1963-1993 Dodge Ram 2500 and 3500
• 1994-2002 Dodge Ram 2500 (V8 Only)
• 2004-2006 Dodge Ram SRT-10

Plymouth

• 1966 Belvedere
• 1966 Satellite
• 1968-1972 Road Runner
• 1967-1971 GTX
• 1970-1971 'Cuda

Ford

• 1955-1985 Ford 3/4 Ton Trucks
• 1955-1976 Ford 1 Ton Trucks
• 1980-1998 Ford E200/E250/E350 vans

Chevrolet

• 1964-1977 Chevrolet and GMC 3/4-ton pickups
• 1975-1987 Chevrolet and GMC 1-ton pickups and Suburbans
• 1979-1991 Chevrolet and GMC 1-ton vans
• 2001-2010 Chevrolet and GMC 1-ton vans (Uncommon)

Jeep

• 1969-1988 Jeep J-20, J-2000 and J-4000 pickups

[Cadpat]

Exploded Diagram of Dana Model 35 Rear Axle for 2007, 2008, 2009 and 2010 Jeep Wrangler JK:
1. Pinion Yoke Nut
2. Driveshaft Yoke Flange
3. Pinion Yoke Washer
4. Drive Pinion Slinger
5. Drive Pinion Seal
6. Drive Pinion Bearing Front (Cup and Cone)
7. Crush Sleeve
11. Drive Pinion Bearing Kit, Rear Bearing
12. Pinion Shaft Shim Kit (.035 – .039)
13. Ring and Pinion Gear Kit (DMF) 4.10 Ratio
14. Differential Bearing (Consists Of 2 Bearings And 2 Cups)
15. Differential Shaft Pin, (DSA) Anti-Spin Differential
16. Carrier Shim Set
17. Differential Bolt, Hex Flange Head, 7/16 X 14 X 2.25
19. Axle Shaft Seal Retainer (Right or Left)
20. Stud, Hub (Right or Left)
21. Backing Plate To Axle Housing Nut (Right or Left)
22. Axle Drive Shaft Seal
23. Axle Shaft Ring (Right or Left)
24. Axle Shaft Bearing (Right Or Left)
25. Axle Shaft (Right Side)
26. Differential Cover
27. Differential Cover Plug
28. RTV Sealant
29. Bolt Kit
30. Axle Vent Bolt (Lower)
31. Vent Tube Clip (Lower)
32. Axle Vent
33. Vent Tube Clip (Upper)
34. Differential Cover Bolt, Hex Flange Head, 5/16-18x.900
35. Mopar® Center Differential Gear Kit
36. Differential Shaft
37. Drive Pinion Bearing Shim .035
38. Mopar Limited Slip Differential Additive

[Cadpat]

Suzuki Samurai Axle Exploded View and Parts Name

Canon Flash Light 420EX

Parts Name:
1. Oil Seal;
2. Bearing;
3. Carrier;
4. Joint flange;
5. Bearing preload adjusting spacer;
6. Shim;
7. Bearing;
8. Bearing adjuster;
9. Side bearing;
10. Adjuster lock plate;
11. Bevel gear pinion set;
12. Bolt;
13. Rear axle housing;
14. Front axle housing;
15. Bolt;
16. Oil level plug;
17. Gasket;
18. Oil drain plug;
19. Right case;
20. Thrust washer;
21. Joint;
22. Thrust washer;
23. Pinion shaft No. 2;
24. Pinion shaft No. 1;
25. Side gear set;
26. Left case

[Cadpat]

Intérieur de la poche

[Ti-Toy]

Petite comparaison...



Zuk vs LC



Et la



8'' toy vs 9.25'' LC





Never pay again for live sex! | Hot girls doing naughty stuff for free! | Chat for free!

[mathpar4]

4.10 les 2 pignonnes??

[Ti-Toy]

Envoyé par mathpar4

4.10 les 2 pignonnes??

Oui... J'aurais du prendre la photo avec du 3.xx sa aurais été encore plus gros...



Never pay again for live sex! | Hot girls doing naughty stuff for free! | Chat for free!

[marioo]

gm 9.25 ifs k2500 8bolt au roue

Light Truck Chevrolet - 1988 - K2500 PICKUP 4WD - FRONT AXLE-FRONT SUSPENSION-STEERING - 1988-1991 K2 DIFFERENTIAL CARRIER/FRONT AXLE (8600 GVWR C6P)1988-1991 K3 DIFFERENTIAL CARRIER/FRONT AXLE

[Lemay]

Nissan hardbody 86.5 - 95
4 cyl: C200 arriere (200mm ring gear) et R180 (180mm ring gear IFS) avant
V6: Niss H233B (233mm ring gear) Arriere et R200A (200mm ring gear IFS) avant * sauf Hardbody 1Ton, 2WD seulement

Pathfinder 86.5-2004/Xterra 00-04 : arriere H233B (Path: quelque tres rare exception 4 cyl au US ont le C200 86.5-88/89)
Avant: R200A IFS

Gearing & clarification:

HG43 - Found on Pathfinders, V6 Hardbodies, and a few '99 Frontiers - H233B rear / R200 front, 4.375:1 gearing. On the 2000+ 33 spline axles, the HG43 has a 4.363 ratio, however this is not a common axle code on the later models.

HG46 - found on auto equipped pathfinders, 96-97 hardody 4 bangers, many Xterras and Frontiers. This one has some variation. Pre-2000 versions are the H233B axle with 4.625:1 gearing (31 spline axles). 2000+ is the H233B axle with 4.636:1 gearing (33 spline axles). Typically comes with an R200 front axle, with the exception being in the '96-97 Hardbody pickups - those had an H233B / R180 combination. Axle shafts in the H233B were 31 spline up to about 2000, where they switched to 33 spline shafts. All Xterras and R50 Pathfinders received the 33 spline axles. In Frontiers, it can be a crapshoot if you have a '99-'00 model, though it is believed that the switchover was at or near 2/00 production date.

HG49 - found in mid year 2001+ Frontiers and Xterras. H233B / R200 combo with 4.90:1 gears.

[repmo]

ca c'est une citation de Blunt, j'trouvais ca interescent à mettre ici

Pour te motiver, et arrêter de faire jaser ceux qui pensent automatiquement qu'un dana 60 a autant de clearance qu'un différentiel 5 tonnes de 10 roues, voici quelques mesures de différents axle de l'axe centrale du tube du différentiel jusqu'au point le plus bas de la poche:

Dana 30 = 4 5/8"
Ford 8.8 = 5 5/8"
Dana 44 = 5 1/2''
Dana 60 = 5 7/8" (sans shave)

Si qqn connait les mesures, j'aimerais qu'on y ajoute les mesures de dana 70 et 80 ainsi que ce que ca peut donner une fois shaver